{"product_id":"flex40406-1-eye-strap-arm-highlift-with-tail-and-set-screws","title":"FLEX40406.1 EYE STRAP ARM HIGHLIFT WITH TAIL AND SET SCREWS","description":"\u003cul\u003e\n\u003cli\u003eEye strap arm for Flexxifinger Triple S HighLift crop lifters (lifter model 70406)\u003c\/li\u003e\n\u003cli\u003eIncludes spring steel tail and set screws (per the Flexxifinger dealer parts listing for Triple S HighLift 70406: eye strap arm 40406, spring steel tail 32321, set screws 32296)\u003c\/li\u003e\n\u003cli\u003eThe eye-strap method of attaching the lifter's arm and riser to the rail creates a highly adjustable product that can be angled to suit your header or crop type\u003c\/li\u003e\n\u003cli\u003eTriple S HighLift is an all-metal lifter for tall, heavy crops; recommended for auger headers; generally leaves 75-100 mm (3-4 inch) stubble\u003c\/li\u003e\n\u003cli\u003eTriple S series uses patented QD attaching and detaching technology and can be removed or installed in 3-5 minutes per header after initial installation\u003c\/li\u003e\n\u003cli\u003eSold individually\u003c\/li\u003e\n\u003cli\u003eParts diagram: \u003ca href=\"https:\/\/flexxifinger.com\/files\/Dealer_binder_information_EURO.pdf\"\u003eFlexxifinger dealer binder (parts listings and diagrams)\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eTechnical data\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eFits the Triple S HighLift crop lifter 70406 — the eye strap arm assembly, complete with tail and set screws\u003c\/li\u003e\n\u003cli\u003eTriple S lifters fit all systems that have a guard finger in front of the knife, via a universal-fit rail\u003c\/li\u003e\n\u003cli\u003eThe HighLift lifts heads higher above the knife than the MidCut or European and helps stand the crop up in front of the auger for more efficient threshing, with an adjustable tail length to suit crop and field conditions, including Vario-style headers\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eInstallation\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eAdjust the lifter angle with the eye strap: using a 3\/4 in. (19 mm) wrench, loosen the adjustment bolt, then lift or lower the eye strap to change the angle of the lifter — the ideal operating condition is achieved when the riser is angled at 25 degrees\u003c\/li\u003e\n\u003cli\u003eSet the lifters 1\/4 in. (6 mm) to 3\/4 in. (19 mm) from the ground, with the back half of the shoe — not the point — contacting the ground first; if the point contacts the ground first, the lifter is likely to break during use and may damage the harvesting equipment\u003c\/li\u003e\n\u003cli\u003eSet all the lifters to the same angle so they form a straight line when viewed down the row, so all lifters work in unison, then tighten the adjustment bolt on all lifters\u003c\/li\u003e\n\u003cli\u003eAdjust the tail length (HighLift only): loosen the set screws on the brim of the riser, pull out or push in the tail to the required length to accommodate the crop — the length of the tail should not exceed 5 in. (13 cm) past the brim of the riser — then tighten the set screws to keep the tail in place\u003c\/li\u003e\n\u003cli\u003eCombine 100 ft. (30 m), then readjust the angle of the lifters as required\u003c\/li\u003e\n\u003cli\u003eInstallation and Adjustment Instructions: \u003ca href=\"https:\/\/flexxifinger.com\/files\/Triple_S_Lifter_Instructions.pdf\"\u003eTriple S Installation and Adjustment Instructions (PDF)\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eTips \u0026amp; tricks\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eTail length caution: a tail length exceeding 5 in. (13 cm) past the brim of the riser increases the likelihood of causing damage to the lifter and\/or harvest equipment during use\u003c\/li\u003e\n\u003cli\u003eSet the reel so that the upward motion begins where the lifter tail ends; where possible, adjust the reel fingers so they are 20 degrees advanced at the tip of the finger as compared to the bar of the reel, so the reel and the lifters work in unison\u003c\/li\u003e\n\u003cli\u003eTriple S HighLift lifters are made of steel and will not bend — use extreme caution when travelling over irrigation ruts, sprayer and tractor ruts, large cracks in the ground and other uneven ground conditions\u003c\/li\u003e\n\u003cli\u003eReplacement wear parts on the same lifter: the spring steel tail is part 32321 and the set screws are part 32296\u003c\/li\u003e\n\u003c\/ul\u003e\n","brand":"Flexxifinger","offers":[{"title":"Default Title","offer_id":67843593142574,"sku":"FLEX40406.1","price":71.99,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0039\/9166\/6737\/files\/highlift-parts-view_52213e7b-e4e9-4a63-96f7-121289e6895d.webp?v=1793046415","url":"https:\/\/agri-auto.com\/fr\/products\/flex40406-1-eye-strap-arm-highlift-with-tail-and-set-screws","provider":"Saskatoon Agri-Auto Parts Inc.","version":"1.0","type":"link"}